FAQ in english

All about J2534 driver
Все о драйвере J2534
User avatar
kolyandex
Администратор
Posts: 442
Joined: 08 Dec 2019, 13:33
Location: Novosibirsk
Contact:

Re: FAQ in english

Post by kolyandex » 23 May 2020, 10:04

kernel wrote:
22 May 2020, 15:48
Only errors are asc systm issue and 4wd issue, However those errors were there before key programming. Is there an option in the MUT III to check to see if the key is present and working? should I try programming again? just not sure if that will work as it would be considered a used key now and it would be able to be reprogrammed, or am I incorrect?
Hm. Try to manually turn on starter relay, if all ok, engine will started.
In backup we trust.

kernel
Posts: 6
Joined: 08 May 2020, 16:55

Re: FAQ in english

Post by kernel » 28 May 2020, 14:54

kolyandex wrote:
23 May 2020, 10:04
kernel wrote:
22 May 2020, 15:48
Only errors are asc systm issue and 4wd issue, However those errors were there before key programming. Is there an option in the MUT III to check to see if the key is present and working? should I try programming again? just not sure if that will work as it would be considered a used key now and it would be able to be reprogrammed, or am I incorrect?
Hm. Try to manually turn on starter relay, if all ok, engine will started.
It now turns over, I had to trace the starter line and found the issue, It had nothing to do with the driver or MUT III. Thank you for all your help.

Paulo_evo
Posts: 3
Joined: 28 Jul 2020, 09:07

Re: FAQ in english

Post by Paulo_evo » 28 Jul 2020, 10:47

So, the most complete package costs US$ 160,00, is it correct? 150 USD for version 3 + 10 USD for add-on for Nippon Seiki meters with MB91F223 CPU (read/write EEPROM, only for version 3)?

User avatar
kolyandex
Администратор
Posts: 442
Joined: 08 Dec 2019, 13:33
Location: Novosibirsk
Contact:

Re: FAQ in english

Post by kolyandex » 28 Jul 2020, 10:50

Paulo_evo wrote:
28 Jul 2020, 10:47
So, the most complete package costs US$ 160,00, is it correct? 150 USD for version 3 + 10 USD for add-on for Nippon Seiki meters with MB91F223 CPU (read/write EEPROM, only for version 3)?
Yep
In backup we trust.

professor_jonny
Posts: 11
Joined: 31 Jul 2020, 11:57

Re: FAQ in english

Post by professor_jonny » 31 Jul 2020, 12:27

Code: Select all

— k-line (OBD, ISO-MMC, KWP) only on pin 7 (look schematics diagram). ~ before 2000 year vehicles not working.
I'm guessing the emulator currently does not support kline with any vehicle pre 2000?

Is this something that will be added in the future?

I'm wanting to use mut-iii to be able to view fault codes with the srs airbag system, but my car is a 1998 RVR sportsgear x3 im guessing the above means it wont work with my car

User avatar
kolyandex
Администратор
Posts: 442
Joined: 08 Dec 2019, 13:33
Location: Novosibirsk
Contact:

Re: FAQ in english

Post by kolyandex » 31 Jul 2020, 15:33

professor_jonny wrote:
31 Jul 2020, 12:27
I'm guessing the emulator currently does not support kline with any vehicle pre 2000?
Is this something that will be added in the future?
I'm wanting to use mut-iii to be able to view fault codes with the srs airbag system, but my car is a 1998 RVR sportsgear x3 im guessing the above means it wont work with my car
Do you have schematics for that car?
Original VCI-Lite can operate only with CAN and k-line without support old protocols, that's why it impossible.
In backup we trust.

professor_jonny
Posts: 11
Joined: 31 Jul 2020, 11:57

Re: FAQ in english

Post by professor_jonny » 31 Jul 2020, 20:54

kolyandex wrote:
31 Jul 2020, 15:33

Do you have schematics for that car?
Original VCI-Lite can operate only with CAN and k-line without support old protocols, that's why it impossible.
I can log in evoscan using muu-ii 1995-1999 protocol same as evo4/5/6
I can flash and read the ecu using ecuflash using mitsukernel evo 5/6 and memory layout is for h839f with mh7202f MCU

The schematics I cant find as the car was only produced in limited numbers for motorsport it is a 4g63t engine in ralliart trim only 500 produced I believe in 1998 and 1999.

More info here and pictures of ecu:
https://www.evolutionm.net/forums/other ... uning.html

User avatar
kolyandex
Администратор
Posts: 442
Joined: 08 Dec 2019, 13:33
Location: Novosibirsk
Contact:

Re: FAQ in english

Post by kolyandex » 01 Aug 2020, 02:47

Can you take a photo of OBD connector wires side?
In backup we trust.

professor_jonny
Posts: 11
Joined: 31 Jul 2020, 11:57

Re: FAQ in english

Post by professor_jonny » 03 Aug 2020, 08:56

kolyandex wrote:
01 Aug 2020, 02:47
Can you take a photo of OBD connector wires side?
As below:
obd.jpg
You do not have the required permissions to view the files attached to this post.

User avatar
kolyandex
Администратор
Posts: 442
Joined: 08 Dec 2019, 13:33
Location: Novosibirsk
Contact:

Re: FAQ in english

Post by kolyandex » 04 Aug 2020, 07:38

Try to use trial version and connect to engine ECU viewtopic.php?f=14&t=16
In backup we trust.

Post Reply